CFM-"Whispering Witch" mounted on a travers with lid halves (for retrofitting/as replacement)
Product number:
5000081
Product information
CFM "Whispering Witch" - the original from Mellrichstadt!
Only available for CFM-honey extractors of art. no. 5004300, 5010400 and 5037000 with distance between holes centre to centre 525 mm and 630 mm as well as our current extractors Nr. 5002500, 5009400, 5014400 und 5055012
Technical data:
• Direct drive motor 40 W / 230 V CFM-"Whispering witch"
• Very quiet drive even at full speed
• Speed control 80 - 350 rpm
• Stainless steel traverse with hinged acrylic glass lid halves
• Safety device
When you order please advise:
• Inner tank Ø
• Shaft Ø at the top and bottom
• Distance between the 2 holes for the screws which hold the traverse measured from the middle of the holes.
• If you replace a manual drive please advise length of the driver below the traverse
Please note: If you have different measurements and we need to customize a surcharge applies!
Only available for CFM-honey extractors of art. no. 5004300, 5010400 and 5037000 with distance between holes centre to centre 525 mm and 630 mm as well as our current extractors Nr. 5002500, 5009400, 5014400 und 5055012
Technical data:
• Direct drive motor 40 W / 230 V CFM-"Whispering witch"
• Very quiet drive even at full speed
• Speed control 80 - 350 rpm
• Stainless steel traverse with hinged acrylic glass lid halves
• Safety device
When you order please advise:
• Inner tank Ø
• Shaft Ø at the top and bottom
• Distance between the 2 holes for the screws which hold the traverse measured from the middle of the holes.
• If you replace a manual drive please advise length of the driver below the traverse
Please note: If you have different measurements and we need to customize a surcharge applies!
Login
accessories
5009400
CFM-Tangential extractor Ø 55cm, manual drive, 4 frames
Our basic model of the CFM-Honey extractors with manual drive
Advantages are the compact design, the cage without middle axis and the fact that you can run this honey extractor without electricity.
This extractor is equipped with a honey tap, has two practical handles at the tank and is suitable for a lot of the common frame sizes.
For cleaning just loosen the two screws of the traverse and take off the drive incl. the lids.
Suitable for:
• 4 deep frames up to 31 cm side bar length or 8 shallow frames up to 15 cm side bar length
• Frame sizes: Zander, German Standard, Langstroth, Zander-Dadant, Freudenstein, Gerstung, Kuntzsch, Dadant
Technical details:
• Manual drive with hinged lid halfs
• Inner tank Ø 55 cm, welded bottom without gap
• Tank bottom with slope to the outlet
• Outlet: 1 1/2" honey tap, welded at bottom level
• Handles at the lower end of the tank
• Grid area of the cage 32 x 46 cm
• Without middle axis (frames can be turned inside the cage)
• Material: Edelstahl-Rostfrei
• Loading height: 100 cm
• Distance from floor to the tap 38 cm
• Can be modified to extract radial with a radial cage
Included in the delivery:
1 pack with hexagonal screws and nuts for the feet, one socket wrench no. 13 and a yellow sealant for the bottom bearing.
Weight with/without wrapping: 26 kg / 32 kg
Wrapping: cardboard box
Chargeable weight: 38 kg
Spare parts and accessories:
Item no. 6000070 Ball for bearing
Item no. 6300061 Rubber feet
Item no. 6000074 Food lubricant grease for bottom bearing 20 g
Item no. 23045007 Sealant for bottom bearing
Item no. 5003244 4 frames tangential cage
Item no. 5003709 9 shallow frames radial cage
Acrylic glass lid half on request
5055012
CFM-Honey extractor 12 shallow frames, radial, manual drive
The smallest of our CFM-Honey radial extractors with manual drive
Advantages are the compact design and the fact that you can run this honey extractor without electricity.
This extractor is equipped with a honey tap and has two practical handles at the tank.
For cleaning just loosen the two screws of the traverse and take off the drive incl. the lids.
Suitable for:
• 12 shallow frames up to 16 cm side bar length and 42 mm side bar width
• Frame sizes: Dadant shallow frames, Zander shallow frames, German Standard shallow frames, Langstroth shallow frames
Technical details:
• Manual drive with hinged lid halfs
• Inner tank Ø 55 cm, welded bottom without gap
• Tank bottom with slope to the outlet
• Outlet: 1 1/2" honey tap, welded at bottom level
• Handles at the lower end of the tank
• Radial cage for 12 shallow frames
• Material: Edelstahl-Rostfrei
• Loading height: 100 cm
• Total height: 110 cm
• Distance from floor to the tap 38 cm
• Can be modified to extract tangential
Included in the delivery:
1 pack with hexagonal screws and nuts for the feet, one socket wrench no. 13 and a yellow sealant for the bottom bearing.
Weight with/without wrapping: XX kg / XX kg
Wrapping: cardboard box
Chargeable weight: 26 kg
Spare parts and accessories:
Item no. 6000070 Ball for bearing
Item no. 6300061 Rubber feet
Item no. 6000074 Food lubricant grease for bottom bearing 20 g
Item no. 23045007 Sealant for bottom bearing
Item no. 5203712 12 frames radial cage
Item no. 5303712 3 grids
Item no. 5003244 4 frames tangential cage 32 x 46cm
Acrylic glass lid half on request
5009471
CFM-Tangential extractor Ø 55cm, 4 frames with 110W "extractor witch"
Our basic model of the CFM-Honey extractors with our "Extractor Witch".
Advantages are the compact design and the cage without middle axis.
This extractor is equipped with a honey tap, has two practical handles at the tank and is suitable for a lot of the common frame sizes
For cleaning just loosen the two screws of the traverse and take off the drive incl. the lids.
Suitable for:
• 4 deep frames up to 31cm side bar length or 8 shallow frames up to 15 cm side bar length
• Frame sizes: Zander, German Standard, Langstroth, Zander-Dadant, Freudenstein, Gerstung, Kuntzsch, Dadant
Technical details:
• Top drive with security switch
• Motor power 110 W / 230 V
• Hinged acrylic glass lid halves
• Inner tank Ø 55 cm, welded bottom without gap
• Tank bottom with slope to the outlet
• Outlet: 1 1/2" honey tap, welded at bottom level
• Handles at the lower end of the tank
• Grid area of the cage 32 x 46 cm
• Without middle axis (frames can be turned inside the cage)
• Material: Stainless steel
• Loading height: 100 cm
• Distance from floor to the tap 38 cm
• Can be modified to extract radial with a radial cage
Included in the delivery:
1 pack with hexagonal screws and nuts for the feet, one socket wrench no. 13 and a yellow sealant for the bottom bearing.
Weight with/without wrapping: 29 kg / 35 kg
Wrapping: cardboard box
Chargeable weight: 40 kg
Spare parts and accessories:
Item no. 6000070 Ball for bearing
Item no. 6300061 Rubber feet
Item no. 6000074 Food lubricant grease for bottom bearing 20 g
Item no. 23045007 Sealant for bottom bearing
Item no. 5003244 4 frames tangential cage
Item no. 5003709 9 shallow frames radial cage
Acrylic glass lid half on request
5014400
CFM-Tangential extractor Ø 63cm, manual drive, 4 frames
The allrounder of the CFM-Honey extractors with manual drive
This tangential extractor is even suitable for the large frame sizes like Dadant and German Standard 1 1/2. The cage is without middle axis so you can turn the frames inside the cage.
This extractor is equipped with a honey tap, has two practical handles at the tank and is suitable for a lot of the common frame sizes.
For cleaning just loosen the two screws of the traverse and take off the drive incl. the lids.
Suitable for:
• 4 deep frames up to 37 cm side bar length or 8 shallow frames up to 18 cm side bar length
• Frame sizes: Zander, German Standard, Langstroth, Zander-Dadant, Freudenstein, Gerstung, Kuntzsch, Dadant, German Standard 1 1/2 or Swiss frames
Technical details:
• Manual drive with hinged lid halfs
• Inner tank Ø 63 cm, welded bottom without gap
• Tank bottom with slope to the outlet
• Outlet: 1 1/2" honey tap, welded at bottom level
• Handles at the lower end of the tank
• Grid area of the cage 38 x 46 cm
• Without middle axis (frames can be turned inside the cage)
• Material: Edelstahl-Rostfrei
• Loading height: 100 cm
• Distance from floor to the tap 38 cm
• Can be modified to extract radial with a radial cage
Included in the delivery:
1 pack with hexagonal screws and nuts for the feet, one socket wrench no. 13 and a yellow sealant for the bottom bearing.
Weight with/without wrapping: 31 kg / 37 kg
Wrapping: cardboard box
Chargeable weight: 42 kg
Spare parts and accessories:
Item no. 6000070 Ball for bearing
Item no. 6300061 Rubber feet
Item no. 6000074 Food lubricant grease for bottom bearing 20 g
Item no. 23045007 Sealant for bottom bearing
Item no. 5003840 4 frames tangential cage
Item no. 5203815 15 shallow frames radial cage
Acrylic glass lid half on request
5002500
CFM-Tangential extractor Ø 43cm, manual drive, 4 frames
The smallest CFM-Honey extractors with manual drive
Advantages are the very small dimension, the cage without middle axis and the fact that you can run this honey extractor without electricity.
This extractor is equipped with a honey tap, has two practical handles at the tank and is suitable for a lot of the common frame sizes.
For cleaning just loosen the two screws of the traverse and take off the drive incl. the lids.
Suitable for:
• 4 deep or shallow frames up to 23.5 cm side bar length
• Frame sizes: Zander, German Standard, Langstroth
Technical details:
• Manual drive with hinged lid halfs
• Inner tank Ø 43 cm, welded bottom without gap
• Tank bottom with slope to the outlet
• Outlet: 1 1/2" honey tap, welded at bottom level
• Handles at the lower end of the tank
• Grid area of the cage 24.5 x 46 cm
• Without middle axis (combs can be turned inside the cage)
• Material: Edelstahl-Rostfrei
• Loading height: 100 cm
• Distance from floor to the tap 38 cm
Included in the delivery:
1 pack with hexagonal screws and nuts for the feet, one socket wrench no. 13 and a yellow sealant for the bottom bearing.
Weight with/without wrapping: 21 kg / 26 kg
Wrapping: cardboard box
Chargeable weight: 32 kg
Spare parts and accessories:
Item no. 6000070 Ball for bearing
Item no. 6300061 Rubber feet
Item no. 6000074 Food lubricant grease for bottom bearing 20 g
Item no. 23045007 Sealant for bottom bearing
Item no. 5002443 4 frames tangential cage
Acrylic glass lid half on request
5014471
CFM-Tangential extractor Ø 63cm, 4 frames with 110W "extractor witch"
The allrounder of the CFM-Honey extractors with our "Extractor Witch".
This tangential extractor with motor is even suitable for large frames like Dadant and German Standard 1 1/2. The cage is without middle axis so the frames can be turned inside the cage.
This extractor is equipped with a honey tap, has two practical handles at the tank and is suitable for a lot of the common frame sizes
For cleaning just loosen the two screws of the traverse and take off the drive incl. the lids.
Suitable for:
• 4 deep deep frames up to 31cm side bar length or 8 shallow frames up to 15 cm side bar length
• Frame sizes: Zander, German Standard, Langstroth, Zander-Dadant, Freudenstein, Gerstung, Kuntzsch, Dadant, German Standard 1 1/2 and Swiss frames
Technical details:
• Top drive with security switch
• Motor power 110 W / 230 V
• Hinged acrylic glass lid halves
• Inner tank Ø 63 cm, welded bottom without gap
• Tank bottom with slope to the outlet
• Outlet: 1 1/2" honey tap, welded at bottom level
• Handles at the lower end of the tank
• Grid area of the cage 38 x 46 cm
• Without middle axis (frames can be turned inside the cage)
• Material: Edelstahl-Rostfrei
• Loading height: 100 cm
• Distance from floor to the tap 38 cm
• Can be modified to extract radial with a radial cage
Included in the delivery:
1 pack with hexagonal screws and nuts for the feet, one socket wrench no. 13 and a yellow sealant for the bottom bearing.
Weight with/without wrapping: 34 kg / 40 kg
Wrapping: cardboard box
Chargeable weight: 46 kg
Spare parts and accessories:
Item no. 6000070 Ball for bearing
Item no. 6300061 Rubber feet
Item no. 6000074 Food lubricant grease for bottom bearing 20 g
Item no. 23045007 Sealant for bottom bearing
Item no. 5003840 4 frames tangential cage
Item no. 5203818 18 shallow frames radial cage
Acrylic glass lid half on request
5002571
CFM-Tangential extractor Ø 43 cm, 4 frames with motor 110W
The smallest CFM-Honey extractors with our "Extractor Witch".
Advantages are the very small dimension and the cage without middle axis.
This extractor is equipped with a honey tap, has two practical handles at the tank and is suitable for a lot of the common frame sizes.
For cleaning just loosen the two screws of the traverse and take off the drive incl. the lids.
Suitable for:
• 4 deep or shallow frames up to 23.5 cm sidebar length
• Frame sizes: Zander, German Standard, Langstroth
Technical details:
• Direct drive with security switch
• Motor power 110 W / 230 V
• Hinged acrylic glass lid halves
• Inner tank Ø 43 cm, welded bottom without gap
• Tank bottom with slope to the outlet
• Outlet: 1 1/2" honey tap, welded at bottom level
• Handles at the lower end of the tank
• Grid area of the cage 24.5 x 46 cm
• Without middle axis (combs can be turned inside the cage)
• Material: Edelstahl-Rostfrei
• Loading height: 100 cm
• Distance from floor to the tap 38 cm
Included in the delivery:
1 pack with hexagonal screws and nuts for the feet, one socket wrench no. 13 and a yellow sealant for the bottom bearing.
Weight with/without wrapping: 24 kg / 29 kg
Wrapping: cardboard box
Chargeable weight: 35 kg
Spare parts and accessories:
Item no. 6000070 Ball for bearing
Item no. 6300061 Rubber feet
Item no. 6000074 Food lubricant grease for bottom bearing 20 g
Item no. 23045007 Sealant for bottom bearing
Item no. 5002443 4 frames tangential cage
Acrylic glass lid half on request